(!)Due to Microsoft's end of support for Internet Explorer 11 on 15/06/2022, this site does not support the recommended environment.
- Scheduled Maintenance Notice: This site will be unavailable due to scheduled maintenance from 9:00 19/4/2026 to 7:00 (MYT) 20/4/2026. We apologize for the inconvenience.
- [Notice] Japan & China Golden Week holidays will start from 29 April to 6 May 2026. Kindly expect longer response from suppliers and possible delivery delay due to high volume of shipments after holiday. Early order placement is recommended. More details
- [Announcement] MISUMI Malaysia website new user interface. Clearer navigation, easy product search and more. Explore now! May contact us at (60) 3 7890 6399 for any inquiries.
Shafts - Both Ends Tapped Hollow Shafts - Not applicable to Both Ends Tapped Hollow Shafts / Both Ends Tapped Hollow with Wrench Flats
"[Features] This shaft facilitates customers to arrange wiring, because the wire can be pierced into the inside of the shaft and contributes to weight saving of equipment, because the shaft is hollow."
Part Number
Configured Part Number is shown.
[ ! ]About Hollow Shaft Wall Thickness Deviations, please see >> P.111
[ ! ]Features of Low Temp. Black Chrome Plating
>>P.128
[ ! ]Circularity and O.D. tolerance may not meet precision specification in areas approximately 15mm from wrench flats machined ends.
[ ! ]Circularity, Straightness, Perpendicularity and Changes in Hardness >>P.111
[ ! ]Low temp. black chrome plating is not applied to the inside of hollow shafts, taps, bored holes and lateral holes, and may rust.
[ ! ]Annealing required for wrench flats machining and shaft end threading (effective thread length + approx. 10mm) may lower hardness. >>P.112
>>P.128
[ ! ]Circularity and O.D. tolerance may not meet precision specification in areas approximately 15mm from wrench flats machined ends.
[ ! ]Circularity, Straightness, Perpendicularity and Changes in Hardness >>P.111
[ ! ]Low temp. black chrome plating is not applied to the inside of hollow shafts, taps, bored holes and lateral holes, and may rust.
[ ! ]Annealing required for wrench flats machining and shaft end threading (effective thread length + approx. 10mm) may lower hardness. >>P.112
| Type | [ M ]Material | [ H ]Hardness | [ S ]Surface Treatment | |
| Both Ends Tapped | Both Ends Tapped with Wrench Flats | |||
| SPJW | SPWR | SUJ2 | Effective Hardened Depth of Induction Hardened >>P.112 SUJ2 58HRC~ SUS440C equivalent 56HRC~ | - |
| SSPJW | SSPWR | SUS440C equivalent | ||
| PSPJW | PSPWR | SUJ2 | Hard Chrome Plating Plating Hardness: HV750 ~ Plating Thickness: 5µ or More | |
| RSPJW | RSPWR | SUJ2 | Low Temp. Black Chrome Plating | |
Specifications
• Both Ends Tapped Hollow Shafts
| Part Number | - | L | - | M | - | N | - | SC |
| SPJW20 SPWR30 | - - | 500 680 | - - | M16 M20 | - - | N16 N20 | - | SC10 |
■Both Ends Tapped Hollow Shafts
| Part Number | L 1mm Increment | M (Coarse Thread) N (Coarse Thread) | D Tol. | d | C | |||||
| Type | D | |||||||||
| Both Ends Tapped Hollow Shafts SPJW SSPJW (* marked sizes only) PSPJW | 6 | 20~600 | 3 | -0.004 -0.012 | 2 | 0.5 or Less | ||||
| *8 | 20~800 (300) | 4 | *5 | -0.005 -0.014 | 3(3) | 0.5 or Less | ||||
| *10 | 20~800 (400) | 5 | *6 | -0.005 -0.014 | 4(4) | 0.5 or Less | ||||
| *12 | 32~1000 (500) | *8 | *T1 (RC1/8) | -0.006 -0.017 | 6(5) | 0.5 or Less | ||||
| *13 | 40~1000 (500) | *10 | *T1 (RC1/8) | -0.006 -0.017 | 7(5) | 0.5 or Less | ||||
| *16 | 48~1200 (600) | *12 | *T2 (RC1/4) | -0.006 -0.017 | 10(6) | 0.5 or Less | ||||
| *20 | 64~1200 (800) | *16 | *T3 (RC3/8) | -0.007 -0.020 | 14(8) | 1.0 or Less | ||||
| *25 | 80~1200 (1000) | *20 | -0.007 -0.020 | 16(10) | 1.0 or Less | |||||
| *30 | 80~1500 (1000) | *20 | -0.007 -0.020 | 17(12) | 1.0 or Less | |||||
| 35 | 96~1500 | 24 | -0.009 -0.025 | 19 | 1.0 or Less | |||||
| 40 | 96~1500 | 24 | 30 | -0.009 -0.025 | 20 | 1.0 or Less | ||||
| 50 | 120~1500 | 30 | -0.009 -0.025 | 26 | 1.0 or Less | |||||
| Part Number | L 1mm Increment | M (Coarse Thread) N (Coarse Thread) | D Tol. | d | C | |||||
| Type | D | |||||||||
| Both Ends Tapped Hollow Shafts Low Temp. Black Chrome Plating RSPJW | 6 | 20~500 | 3 | -0.004 -0.012 | 2 | 0.5 or Less | ||||
| 8 | 20~500 | 4 | 5 | -0.005 -0.014 | 3 | 0.5 or Less | ||||
| 10 | 20~500 | 5 | 6 | -0.005 -0.014 | 4 | 0.5 or Less | ||||
| 12 | 32~500 | 8 | T1 (RC1/8) | -0.006 -0.017 | 6 | 0.5 or Less | ||||
| 13 | 40~500 | 10 | T1 (RC1/8) | -0.006 -0.017 | 7 | 0.5 or Less | ||||
| 16 | 48~500 | 12 | T2 (RC1/4) | -0.006 -0.017 | 10 | 0.5 or Less | ||||
| 20 | 64~500 | 16 | T3 (RC3/8) | -0.007 -0.020 | 14 | 1.0 or Less | ||||
| 25 | 80~500 | 20 | -0.007 -0.020 | 16 | 1.0 or Less | |||||
| 30 | 80~500 | 20 | -0.007 -0.020 | 17 | 1.0 or Less | |||||
| Part Number | L 1mm Increment | M (Coarse Thread), N (Coarse Thread) | Wrench Flats Dimensions | D Tol. | d | C | |||||||
| Type | D | SC | W | ℓ1 | |||||||||
| Both Ends Tapped Hollow Shafts with Wrench Flats SPWR SSPWR (* marked sizes only) PSPWR | 6 | 20~600 | 3 | SC=1mm Increment [ ! ]When D≤25 SC+ℓ1≤L-Nx2 SC≥Mx2 [ ! ]When D≥30 SC+ℓ1≤L SC≥0 [ ! ]Details of Wrench Flats P.112 | 5 | 8 | -0.004 -0.012 | 2 | 0.5 or Less | ||||
| * 8 | 20~800 (300) | 4 | * 5 | 7 | 8 | -0.005 -0.014 | 3 (3) | 0.5 or Less | |||||
| * 10 | 20~800 (400) | 5 | * 6 | 8 | 8 | -0.005 -0.014 | 4 (4) | 0.5 or Less | |||||
| * 12 | 32~1000 (500) | * 8 | *T1 (RC1/8) | 10 | 10 | -0.006 -0.017 | 6 (5) | 0.5 or Less | |||||
| * 13 | 40~1000 (500) | * 10 | *T1 (RC1/8) | 11 | 10 | -0.006 -0.017 | 7 (5) | 0.5 or Less | |||||
| * 16 | 48~1200 (600) | * 12 | *T2 (RC1/4) | 14 | 10 | -0.006 -0.017 | 10 (6) | 0.5 or Less | |||||
| * 20 | 64~1200 (800) | * 16 | *T3 (RC3/8) | 17 | 10 | -0.007 -0.020 | 14 (8) | 1.0 or Less | |||||
| * 25 | 80~1200 (1000) | * 20 | 22 | 10 | -0.007 -0.020 | 16 (10) | 1.0 or Less | ||||||
| * 30 | 80~1500 (1000) | * 20 | 27 | 15 | -0.007 -0.020 | 17 (12) | 1.0 or Less | ||||||
| 35 | 96~1500 | 24 | 30 | 15 | -0.009 -0.025 | 19 | 1.0 or Less | ||||||
| 40 | 96~1500 | 24 | 30 | 36 | 20 | -0.009 -0.025 | 20 | 1.0 or Less | |||||
| 50 | 120~1500 | 30 | 41 | 20 | -0.009 -0.025 | 26 | 1.0 or Less | ||||||
| Part Number | L 1mm Increment | M (Coarse Thread), N (Coarse Thread) | Wrench Flats Dimensions | D Tol. | d | C | |||||||
| Type | D | SC | W | ℓ1 | |||||||||
| Both Ends Tapped Hollow Shafts with Wrench Flats Low Temp. Black Chrome Plating RSPWR | 6 | 20~500 | 3 | SC=1mm Increment [ ! ]When D≤25 SC+ℓ1≤L-Nx2 SC≥Mx2 [ ! ]When D≥30 SC+ℓ1≤L SC≥0 [ ! ]Details of Wrench Flats P.112 | 5 | 8 | -0.004 -0.012 | 2 | 0.5 or Less | ||||
| 8 | 20~500 | 4 | 5 | 7 | 8 | -0.005 -0.014 | 3 | 0.5 or Less | |||||
| 10 | 20~500 | 5 | 6 | 8 | 8 | -0.005 -0.014 | 4 | 0.5 or Less | |||||
| 12 | 32~500 | 8 | T1 (RC1/8) | 10 | 10 | -0.006 -0.017 | 6 | 0.5 or Less | |||||
| 13 | 40~500 | 10 | T1 (RC1/8) | 11 | 10 | -0.006 -0.017 | 7 | 0.5 or Less | |||||
| 16 | 48~500 | 12 | T2 (RC1/4) | 14 | 10 | -0.006 -0.017 | 10 | 0.5 or Less | |||||
| 20 | 64~500 | 16 | T3 (RC3/8) | 17 | 10 | -0.007 -0.020 | 14 | 1.0 or Less | |||||
| 25 | 80~500 | 20 | 22 | 10 | -0.007 -0.020 | 16 | 1.0 or Less | ||||||
| 30 | 80~500 | 20 | 27 | 15 | -0.007 -0.020 | 17 | 1.0 or Less | ||||||
[ ! ]When Mx25+4+Nx2.5+4≤L, tap pilot holes may go through. [ ! ]When L≤Mx2+Nx2, effective depth of larger diameter tap has priority.
[ ! ]Only * marked D, M and N dimensions are applicable to Stainless Steel Shafts. L and d dimensions in ( ) are applicable.
Alterations
Part Number
CAD Data download and 3D preview are not available because the part number has not yet been determined.
- *In order to open the CAD Data download and 3D preview screen, the part number must be fixed.
- Please confirm the part number from "Specification / Dimension"on the left side, and then perform the CAD Data Download / 3D Preview operation.
Loading...
| Part Number |
|---|
| PSPJW16-[30-1200/1]-M12-N12 |
| PSPJW16-[30-1200/1]-M12-NT2 |
| PSPJW16-[30-1200/1]-MT2-N12 |
| PSPJW16-[30-1200/1]-MT2-NT2 |
| PSPJW20-[30-1200/1]-M16-N16 |
| PSPJW20-[30-1200/1]-M16-NT3 |
| PSPJW20-[30-1200/1]-MT3-N16 |
| PSPJW20-[30-1200/1]-MT3-NT3 |
| PSPJW25-[35-1200/1]-M20-N20 |
| SPJW16-[30-1200/1]-M12-N12 |
| SPJW16-[30-1200/1]-M12-NT2 |
| SPJW16-[30-1200/1]-MT2-N12 |
| SPJW16-[30-1200/1]-MT2-NT2 |
| SPJW20-[30-1200/1]-M16-N16 |
| SPJW20-[30-1200/1]-M16-NT3 |
| SPJW20-[30-1200/1]-MT3-N16 |
| SPJW20-[30-1200/1]-MT3-NT3 |
| SPJW25-[35-1200/1]-M20-N20 |
| Part Number | Standard Unit Price | Minimum order quantity | Volume Discount | Days to Ship | Surface Treatment | TEST (Ø) | Length L (mm) | Change Tapped Thread M to Tapered One [MT] 1(RC1/8) 2(RC1/4) 3(RC3/8) | Change Tapped Thread N to Tapered One [NT] 1(RC1/8) 2(RC1/4) 3(RC3/8) | Tapped (Coarse) [M] (mm) | Tapped (Coarse) [N] (mm) |
|---|---|---|---|---|---|---|---|---|---|---|---|
- | 1 Piece(s) | 3 Day(s) | Hard Chrome Plating | 16 | 30 ～ 1200 | - | - | 12 | 12 | ||
- | 1 Piece(s) | 3 Day(s) | Hard Chrome Plating | 16 | 30 ～ 1200 | - | 2 | 12 | - | ||
- | 1 Piece(s) | 3 Day(s) | Hard Chrome Plating | 16 | 30 ～ 1200 | 2 | - | - | 12 | ||
- | 1 Piece(s) | 3 Day(s) | Hard Chrome Plating | 16 | 30 ～ 1200 | 2 | 2 | - | - | ||
- | 1 Piece(s) | 3 Day(s) | Hard Chrome Plating | 20 | 30 ～ 1200 | - | - | 16 | 16 | ||
- | 1 Piece(s) | 3 Day(s) | Hard Chrome Plating | 20 | 30 ～ 1200 | - | 3 | 16 | - | ||
- | 1 Piece(s) | 3 Day(s) | Hard Chrome Plating | 20 | 30 ～ 1200 | 3 | - | - | 16 | ||
- | 1 Piece(s) | 3 Day(s) | Hard Chrome Plating | 20 | 30 ～ 1200 | 3 | 3 | - | - | ||
- | 1 Piece(s) | 3 Day(s) | Hard Chrome Plating | 25 | 35 ～ 1200 | - | - | 20 | 20 | ||
- | 1 Piece(s) | 3 Day(s) | Not Provided | 16 | 30 ～ 1200 | - | - | 12 | 12 | ||
- | 1 Piece(s) | 3 Day(s) | Not Provided | 16 | 30 ～ 1200 | - | 2 | 12 | - | ||
- | 1 Piece(s) | 3 Day(s) | Not Provided | 16 | 30 ～ 1200 | 2 | - | - | 12 | ||
- | 1 Piece(s) | 3 Day(s) | Not Provided | 16 | 30 ～ 1200 | 2 | 2 | - | - | ||
- | 1 Piece(s) | 3 Day(s) | Not Provided | 20 | 30 ～ 1200 | - | - | 16 | 16 | ||
- | 1 Piece(s) | 3 Day(s) | Not Provided | 20 | 30 ～ 1200 | - | 3 | 16 | - | ||
- | 1 Piece(s) | 3 Day(s) | Not Provided | 20 | 30 ～ 1200 | 3 | - | - | 16 | ||
- | 1 Piece(s) | 3 Day(s) | Not Provided | 20 | 30 ～ 1200 | 3 | 3 | - | - | ||
- | 1 Piece(s) | 3 Day(s) | Not Provided | 25 | 35 ～ 1200 | - | - | 20 | 20 |
Loading...
Example
Basic Information
| Basic Shape | Hollow | End Shape (Left) | Tapped | End Shape (Right) | Tapped |
|---|---|---|---|---|---|
| TEST | SUJ2 / SUJ2 Equivalent | Heat Treatment | Induction Hardened | Shaft Fit Tolerance | g6 |
| Hardness | Induction Hardened (58HRC~) |
Specification/Dimensions
-
Surface Treatment
- Not Provided
- Hard Chrome Plating
-
TEST(Ø)
-
Length L(mm)
-
Change Tapped Thread M to Tapered One [MT] 1(RC1/8) 2(RC1/4) 3(RC3/8)
-
Change Tapped Thread N to Tapered One [NT] 1(RC1/8) 2(RC1/4) 3(RC3/8)
-
Tapped (Coarse) [M](mm)
-
Tapped (Coarse) [N](mm)
-
type
- PSPJW
- SPJW
-
CAD
- 2D
- 3D
Days to Ship
-
- All
- 3 Day(s) or Less
Specify Alterations
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Additional Products in this Category
- Linear Shafts - One End Two Tapped Holes - Solid Type / One End Tapped Type / One End Stepped and Tapped Type / Threaded Type
- Linear Shafts - With Retaining Ring Grooves -
- Linear Shafts-One End Stepped, Both Ends Female Thread with Wrench Flats-
- High Precision Linear Shafts - One End Threaded One End Tapped with Undercut / One End Threaded One End Tapped with Undercut and Wrench Flats
- Linear Shafts-Both Ends Threaded
- Linear Shafts-Both Ends Threaded with Wrench Flats / Cross-Drilled Hole
- Linear Shafts-One End Threaded
- Standard LM Shaft
Complementary Products
-
Shaft Supports T-Shaped Slit (Machined) - Standard / Wide
MISUMI_Test Days to Ship : 3 Day(s) or more
-
Oil Free Bushing Housing Units - Standard Flanged - Standard - Built-In Copper Alloy Bushings, Single / Double
MISUMI_Test Standard Price : MYR 58.85- Days to Ship : 1 Day(s) or more
-
Shaft-sliding Linear Bushing Housing Units - Single / Double
MISUMI_Test Standard Price : MYR 63.56- Days to Ship : 1 Day(s) or more
Customers Who Viewed This Item Also Viewed
-
-
-
Hollow Shafts / End-Washers for Linear Shafts - Shaft Ends Configurable
MISUMI_Test
Days to Ship : 6 Day(s) or more
-
-
Linear Shafts-Both Ends Tapped with Wrench Flats / Both Ends Tapped with Cross-Drilled HoleMISUMI_Test
Days to Ship : 3 Day(s) or more
-
High Precision Linear Shafts-Both Ends Tapped / Both Ends Tapped with Wrench FlatsMISUMI_Test
Days to Ship : 7 Day(s) or more
-
-
Linear Shafts - One End Threaded / One End Tapped Hollow
MISUMI_Test
Days to Ship : 4 Day(s) or more
-
Full Length Hardness Guaranteed Shafts - One End / Both Ends Tapped, Short
MISUMI_Test
Days to Ship : 3 Day(s)
-
Shafts - One End Threaded Hollow Shafts - One End Threaded Hollow Shafts with Wrench Flats / One End Threaded Hollow ShaftsMISUMI_Test
Days to Ship : 4 Day(s) or more
-
-
Tech Support
- Factory Automation, Electronics, Tools, & MRO (Maintenance, Repair and Operations)
- Tel：(60) 3 7960 8499 / FAX：(60) 3 7960 7499
- 9:00am - 6:00pm (Monday - Friday)
9:00am - 1:00pm (Saturday) - Technical Inquiry
- Credit Card
- Bank Transfer
Social Media
MISUMI Contact
Copyright © MISUMI Corporation All Rights Reserved.
How can we improve?
How can we improve?
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy
Thank you for your cooperation.
While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.
Customer Privacy Policy